JUMBO TR-7619
-
Load capacity
325 kg
716.50 lbs
(Load capacity is based on < 10.000 cycles) -
Width
19.1 mm
0.75 inch -
Height
76.2 mm
3 inch -
Travel
over extension 130%
-
Fixations
Countersunk holes
-
Open position
Lock out
Lock in - horizontal latch
JUMBO TR - 7619
- Full extension telescopic ball bearing drawer runner
- Three different locking options; lock in, lock out or lock in/lock out front release.
- Supports loads up to 325 kg
- Part of our super heavy duty slide range
- Perfect for extra heavy duty applications such as loading platforms, special vehicles and tooling cabinets.
| article |
length mm/inch
|
travel mm/inch
|
cycles 10.000 kg/lbs
|
cycles 50.000 kg/lbs
|
| 114S31 |
300 mm / 11.8”
|
298 mm / 11.7”
|
225 kg / 496 lbs
|
195 kg / 429.9 lbs
|
| 114S32 |
350 mm / 13.8"
|
366 mm / 14.4"
|
235 kg / 518.1 lbs
|
200 kg / 440.9 lbs
|
| 114S33 |
400 mm / 15.7"
|
398 mm / 15.7”
|
250 kg / 551.2 lbs
|
210 kg / 463 lbs
|
| 114S34 |
450 mm / 17.7"
|
464 mm / 18.3"
|
255 kg / 562.2 lbs
|
220 kg / 485 lbs
|
| 114S35 |
500 mm / 19.7"
|
512 mm / 20.2”
|
260 kg / 573.2 lbs
|
230 kg / 507.1 lbs
|
| 114S36 |
550 mm / 21.7"
|
562 mm / 22.1"
|
265 kg / 584.2 lbs
|
240 kg / 529.1 lbs
|
| 114S37 |
600 mm / 23.6"
|
610 mm / 24”
|
275 kg / 606.3 lbs
|
255 kg / 562.2 lbs
|
| 114S46 |
650 mm / 25.6"
|
660 mm / 26"
|
285 kg / 628.3 lbs
|
265 kg / 584.2 lbs
|
| 114S38 |
700 mm / 27.6”
|
708 mm / 27.9”
|
295 kg / 650.4 lbs
|
280 kg / 617.3 lbs
|
| 114S47 |
750 mm / 29.5"
|
758 mm / 29.8"
|
300 kg / 661.4 lbs
|
290 kg / 639.3 lbs
|
| 114S39 |
800 mm / 31.5”
|
806 mm / 31.7”
|
310 kg / 683.4 lbs
|
300 kg / 661.4 lbs
|
| 114S43 |
850 mm / 33.5"
|
854 mm / 33.6"
|
315 kg / 694.5 lbs
|
300 kg / 661.4 lbs
|
| 114S40 |
900 mm / 35.4”
|
904 mm / 35.6”
|
320 kg / 705.5 lbs
|
310 kg / 683.4 lbs
|
| 114S41 |
1000 mm / 39.4”
|
1000 mm / 39.4”
|
325 kg / 716.5 lbs
|
315 kg / 694.5 lbs
|
| 114S44 |
1100 mm / 43.3"
|
1098 mm / 43.2"
|
305 kg / 672.4 lbs
|
290 kg / 639.3 lbs
|
| 114S42 |
1200 mm / 47.2”
|
1212 mm / 47.7”
|
295 kg / 650.4 lbs
|
280 kg / 617.3 lbs
|
| 114S48 |
1350 mm / 53.1"
|
1358 mm / 53.5"
|
245 kg / 540.1 lbs
|
210 kg / 463 lbs
|
| 114S45 |
1500 mm / 59.1”
|
1504 mm / 59.2”
|
225 kg / 496 lbs
|
195 kg / 429.9 lbs
|
Cabinet side
Metal: M5 / DIN 7984
M5 / M6 / ISO 7380
Drawer side
Metal: M5 / DIN 7984
M5 / M6 / ISO 7380
Load capacity
Load capacity varies as the result of a number of factors. Main factors being the type of slide, length, and ratio between pull-out length and closed length. Another important factor is the number of cycles the slide is required to make. Thomas Regout distinguishes the type of usage between dynamic use and static use. Other factors that influence the load capacity are the features the slide is equipped with, and how it is mounted. Slides are usually mounted sideways so all data concerning load-capacity will be given for sidemounted use. For information about the load capacity with bottom-mounted slides, please contact our sales department.
Dynamic load capacity
In order to determine the dynamic load capacity, all types of Thomas Regout slides have been tested for 50.000 cycles. Their maximum load capacity is compliant with, or exceeds, all common national and international standards including DIN, BIFMA, BS, EN and JIS. The dynamic load capacity figures can be found in the graph below.
Static load capacity
Static load capacity is based on test results at 500, 1.000 and 10.000 cycles. This is most common for industrial purposes. The static load capacity is considerably higher than the dynamic load capacity for all slides. The static load capacity figures listed below were determined for a single length of that slide and are for indication purposes only. Specific applications can be assessed by our R&D department and tested if necessary.
Extension
Extension is defined as the ratio of the travel length of the slide (T) and the lenght of the slide in closed position (L): T = (T/L)*100%. The influence of the extension and length of the slide on the load capacity is shown in the above table.
Thermal resistance
Maximum temperature approx. 80°C, determined by applied plastics and lubrication.
Minimum temperature approx. -20°C, determined by applied plastics and lubrication.
Attention: maximum and minimum temperature are strongly determined by the specific application; duration of exposure, impact and other forces on slide and slide components etc. Values mentioned are indicative, it is important to judge each individual application.
Materials
Thomas Regout slides are available in numerous materials and coatings. Below is an overview of all the materials used in our slides. All our products are compliant with EU ROHS standards.
Sections:
- Cold rolled, low carbon and high yield strength steel according to EN 10268 and EN 10139
- Stainless steel according to EN 10088-2 and EN 10259
Ball cages: HDPE en PA.
Ball bearings: Hardened carbon steel C15, Kl 4 DIN 5401
Locking features: PA, PE, PBTP, TPU, EPDM
Sequence devices: PA, TPU, PP Bumpers: RR PA, TPU, EPDM
Lubrication: Heavy duty ball bearing grease (free of lead), based on mineral oil
Surface treatment (finishing)
Our slides are available in a selection of standard finishes. These finishings can be found in the feature list. The overview provides information about which slide can have a specific surface treatment. If you require an alternative or specialized finish not listed, please contact us for further information.
The JUMBO TR-7619 Full extension telescopic ball bearing drawer runner for extreme conditions and > 300 kg load available with lock in/out & front release.
Below you can download the stepfile, PDF and other technical specifications which belong to the JUMBO TR-7619.
Take a look at our Youtube channel to see the functionality of our combination lock in and hold out feature from our telescopic ball bearing drawer runners.
EU
CAD downloads
DWG downloads
PDF downloads
US
PDF downloads
