General information

ULF HD

General information The custom made ULF HD D is a full extension, 3-beam telescopic ball bearing drawer runner range part of our heavy-duty section with extensions up to 100-130%.
  • Load capacity

    Load capacity

    111 kg
    244.71 lbs
    (Load capacity is based on < 10.000 cycles)
  • Load capacity

    Load capacity

    204 kg
    449.74 lbs
    (Load capacity is based on < 10.000 cycles)
  • Width

    Width

    18,5 mm
    0,73 inch
  • Width

    Width

    17,2 mm
    0,68 inch
  • Width

    Width

    16 mm
    0,63 inch
  • Height

    Height

    55,8 mm
    2,2 inch
  • Travel

    Travel

    full extension 100%
  • Travel

    Travel

    over extension 130%
Product features
ULF HD
Product features The custom made ULF HD D is a full extension, 3-beam telescopic ball bearing drawer runner range part of our heavy-duty section with extensions up to 100-130%.
  • Surface treatments

    • Bright Zinc Chromate - Black passivation
    • Bright zinc chromate - blue passivation
    • Electrodeposited coating
    • Pre-galvanized (Sendzimir)
Technical information
ULF HD
Technical information The custom made ULF HD D is a full extension, 3-beam telescopic ball bearing drawer runner range part of our heavy-duty section with extensions up to 100-130%.
  • Supports loads up to 204 kg
  • Add features such as lock-in, pull in, push to open, hold-out mechanisms
  • Add fixations such as tabs, holes, press inserts, drawer carriers or threated studs
  • The ULF HD can be incorporated into our ISL, UDL and Soft Close Column systems. 

Please visit the product features tab on the product page to find out more information about our customizations. In case of customization or a question about the slide, feature or functionality please contact a sales manager.


Load capacity
Load capacity varies as a result of a number of factors. The main factors being the type of slide, length, and ratio between pull-out length and closed length. Another important factor is the number of cycles the slide is required to make. Thomas Regout distinguishes the type of usage between dynamic use and static use. Other factors that influence the load capacity are the features the slide is equipped with, and how it is mounted. Slides are usually mounted sideways so all data concerning load-capacity will be given for side mounted use. For information about the load capacity with bottom-mounted slides, please contact our sales department.

Dynamic load capacity
In order to determine the dynamic load capacity, all types of Thomas Regout slides have been tested for 100,000 cycles. Their maximum load capacity is compliant with, or exceeds, all common national and international standards including DIN, BIFMA, BS, EN and JIS. The dynamic load capacity figures can be found in the graph below.

Static load capacity
Static load capacity is based on test results at 500, 1000 and 10,000 cycles. This is most common for industrial purposes. The static load capacity is considerably higher than the dynamic load capacity for all slides. The static load capacity figures listed below were determined for a single length of that slide and are for indication purposes only. Specific applications can be assessed by our R&D department and tested if necessary. 

Extension
Extension is defined as the ratio of the travel length of the slide (T) and the length of the slide in a closed position (L): T = (T/L)*100%. The influence of the extension and length of the slide on the load capacity is shown in the graph below

Thermal resistance
Maximum temperature approx. 100°C, determined by applied plastics and lubrication.
Minimum temperature approx. -20°C, determined by applied plastics and lubrication.

Attention: maximum and minimum temperature are strongly determined by the specific application; duration of exposure, impact and other forces on a slide and slide components etc. Values mentioned are indicative, it is important to judge each individual application.

Materials
Thomas Regout slides are available in numerous materials and coatings. Below is an overview of all the materials used in our slides. All our products are compliant with EU ROHS standards.
Sections:
- Cold rolled, low carbon and high yield strength steel according to EN 10268 and EN 10139
- Pre-galvanised low carbon and high yield strength steel according to EN 10147 and EN 10139
- Stainless steel according to EN 10088-2 and EN 10259
Ball cages: Electrolytically galvanized, cold rolled, low carbon and high yield strength steel according to EN 10131 and EN 10152
Ball bearings: Hardened carbon steel C15, Kl 4 DIN 5401
Locking features: PA, PE, PBTP, TPU, EPDM
Sequence devices: PA, TPU, PP Bumpers: RR PA, TPU, EPDM
Lubrication: Heavy-duty ball bearing grease (free of lead), based on mineral oil

Stainless steel
More and more telescopic slides are used in new applications which requires very high corrosion resistance. Due to this fact, Thomas Regout has created the possibility to supply its total product range in stainless steel according to EN 10088-2 and EN 10259. Please inform us about your requirements to create the slide you need. Surface treatment: our slides are available in a selection of standard finishes to the specifications listed below. If you require an alternative or specialized finish not listed, please contact us for further information

Surface treatment (finishing)
Our slides are available in a selection of standard finishes. These finishings can be found in the feature list. The overview provides information about which slide can have a specific surface treatment. If you require an alternative or specialized finish not listed, please contact us for further information.

Product images
ULF HD
Product images The custom made ULF HD D is a full extension, 3-beam telescopic ball bearing drawer runner range part of our heavy-duty section with extensions up to 100-130%.
ULF HD | Ball bearing slides | Thomas Regout International B.V.
ULF HD | Ball bearing slides | Thomas Regout International B.V.
ULF HD | Ball bearing slides | Thomas Regout International B.V.
ULF HD | Ball bearing slides | Thomas Regout International B.V.
CAD Centre
ULF HD
CAD Centre The custom made ULF HD D is a full extension, 3-beam telescopic ball bearing drawer runner range part of our heavy-duty section with extensions up to 100-130%.

EU

General downloads

DWG downloads

PDF downloads

STEP downloads

US

News